MIG WELDING MACHINES
High Quality best efficiency.
Top performmance of Welding Machine
Continuous and Consistent Welding.

Useful for Welding a wide range of Metals like carbon steels, stainless steel, Aluminum and its alloys, etc., provided appropriate consumahlesisgre used.

SALIENT FEATURES:
• Excellent Dynamic Characteristic.
• Fully Copper wound Transformer resulting in Longer life.
• Electronic Controls are housed separately
• Thermal Cut Off Protection provided.
• Separate Wire Feeder Unit provides greater Area of operation and mobility.
• Permanent Magnet Motor ensures smooth wire feeding.
• Light weight feeder easy to move in large fabrication.
• Very Low Power consuming machines.
• Cables are firmly secured with proper end plugs.

WIREFEEDER

Model	250	400	600
Wire dia (mm) Steel	0.8 to 1.6	0.8 to 1.6	0.8 to 1.6
Aluminium	1.2	1.2 to 1.6	1.2 to 1.6
Wire Feed Speed (Meter / Min)	0-18	0-18	0-18
Drive	2 Roll	2 Roll	4 Roll
Weight (Kgs)	7.5 Kgs	7.5 Kgs	10 Kgs

MIG WELDING MACHINES

SALIENT FEATURES:
• Good Arc Characteristics thru EAS(Easy Arc Start) Electronic Control Circuit.
• Excellent welding performance over complete range of welding current (Min to Max) due to very special feed back control circuit. Ideally suited for Automatic weaving.
• Arc stability does not affect owing to Input Power fluctuation and changes in ambient temperature. It is achievable by special control circuit.
• Built-in pre flow and MIG/MAG selector Switch.
• Crater Voltage and Crater current is available.
• Arc Voltage and welding current can be controlled even during welding enhancing the productivity and avoids rejections.
• Provided with MCB in the front panel makes it easy to start anywhere.
• Negligible spatter level dur to auto setting of the lnductance.
• FTT/FAS (Fresh Tip Treatment/Fresh Arc Start) Circuit is provided.

WIREFEEDER

Model	250	400	600
Wire dia (mm) Steel	0.8 to 1.2	0.8 to 1.6	0.8 to 1.6
Aluminium	1.2	1.2 to 1.6	1.2 to 1.6
Wire Feed Speed (Meter / Min)	0-18	0-18	0-18
Drive	2 Roll	2 Roll	4 Roll
Weight (Kgs)	7.5 Kgs	7.5 Kgs	10 Kgs

MIG WELDING MACHINES-MIG-400D
The most economical Welding machine
An answerp to your need from the 'elektroweld' range of Equipments.

• Portable, Compact and Light Weight.
• Excellent Arc Characteristics on both solid and Flux Cored Wires.
• Delivers smooth and stable arc even at Lower Current.
• Save Electricity Cost.
• Unique lntegrated Adjustment Control offer automatic control in Welding Current when arc voltage is changed due to hand movement.
• Very Low spatters due to efficient power source.
• Fresh Arc Start, Smooth and optimum bead shape.
• 100% Indigenous & Service possible up to component level in Printed Circuit Boards.
• Capable of welding all types of metal like SS, MS, & Al etc. An excellent machine for Mig Brazing application also.
• Digital Amps and Volts Meter for accurate and precise setting.

WIRE FEEDER
• Low Inertia and High Torque Printed Circuit Motor allows very smooth wire feeding.
• Dynamic braking is controlled through Transistor switching ensures the longer life of Motor with min overrun of wire.
• Very Light Weight Wire Feeder weight only 9 Kgs.
• Aluminum Cast Feed roll block with single pressure touch system for various dia of wires.
• Remote control mounted on the Wire feeder eliminates the use of remote control cable thus increased reliability and min chance of breakdown.

MIG WELDING MACHINES-MIG-250D
The most economical Welding machine
An answerp to your need from the 'elektroweld' range of Equipments.

• Portable, Compact and Light Weight.
• Excellent Arc Characteristics on both solid and Flux Cored Wires.
• Delivers smooth and stable arc even at Lower Current.
• Save Electricity Cost.
• Unique lntegrated Adjustment Control offer automatic control in Welding Current when arc voltage is changed due to hand movement.
• Very Low spatters due to efficient power source.
• Fresh Arc Start, Smooth and optimum bead shape.
• 100% Indigenous & Service possible up to component level in Printed Circuit Boards.
• Capable of welding all types of metal like SS, MS, & Al etc. An excellent machine for Mig Brazing application also.
• Digital Amps and Volts Meter for accurate and precise setting.

WIRE FEEDER
• Low Inertia and High Torque Printed Circuit Motor allows very smooth wire feeding.
• Dynamic braking is controlled through Transistor switching ensures the longer life of Motor with min overrun of wire.
• Very Light Weight Wire Feeder weight only 9 Kgs.
• Aluminum Cast Feed roll block with single pressure touch system for various dia of wires.
• Remote control mounted on the Wire feeder eliminates the use of remote control cable thus increased reliability and min chance of breakdown.

TIG WELDING MACHINES

SALIENT FEATURES::
• Compensation from main Voltage Fluctuation.
• Capable of Delivering very low Current i.e. 5A.
• Excellent control of Parameters.
• Accurate pulse timings and drop to Crater current.
• Electronics are housed in separate chamber for max safety.
• Thermal and over load Cut Off Circuits Provided.
• Multi purpose Machine can do MMAW/Tig/Pulsed Tig welding.
• Receptacles available for automization with Cold wire feeder.
• Monoblock Thyristors reduce the possibility of breakdowns

H.F UNIT FOR TIG WELDING

SPECIFICATION
(Minitig-150 DC Pulsed Tig Welding Machine.)

Model		Minitig-150 DC
Input Voltage		230V ± 10%/1Ø/50Hz
Input KVA		6.2 KVA Max
Rated Duty Cycle		60%
Max No Load Voltage		100V DC
Rated Load Voltage		32V
DC Out Put Voltage	Tig	5A - 150A
	Manual	5A - 140A
DC Out Put Voltage	Tig	16V - 20V
	Manual	20V - 32V
Initial Crator Current		5A - 150A
Gas Preflow Time		0.3 Sec (Fixed)
Gas Post Flow Time		2 Sec (Fixed)
Pulse duty Cycle		1% - 95%
Pulse Frequency		0.5 Hz - 10 Hz
Dimensions		390mm x 580mm x 620mm
Weight		65 Kgs

LST - 300 DC PULSED TIG WELDING MACHINE

SPECIFICATION

Model		LST-300 DC
Input Voltage		415 ± 10%/3Ø/50 Hz
Input KVA		13.5 KW Max
Rated Duty Cycle		60%
Max No Load Voltage		100V DC
Rated Load Voltage		32V DC
DC OutPut Current	Tig	5A - 300A
	Manual	5A - 300A
DC Out Put Voltage	Tig	16V - 20V
	Manual	20V - 32V
Initial Crator Current		5A - 300A
Up Slope Control Time		0.2 Sec - 10 Sec
Down Slope Control Time		0.2 Sec - 10 Sec
Gas Preflow Time		0 Sec - 3 Sec
Gas Post Flow Time		02 Sec - 23 Sec
Pulse wave		50%
Pulse Frequency		0.5 Hz - 15 Hz
Dimensions		480mm x 580mm x 850mm
Weight		130Kgs

DC Arc Welding Machines (For MMA/TIG)
High Quality best efficiency.
Top performmance of Welding Machine
Continuous and Consistent Welding.

SALIENT FEATURES:
• Assurance of prescribed welding current and Heat Input.
• True vertical Current Welding Characteristic with Higher O.C.V.
• Single range Current control with Remote Control facility.
• Protection against HF interference.
• Stable Arc with Regular Droplet Transfer and elimination of spatter generation.
• Effective Prevention of Electrode Freezing.
• Immunity with AC input Fluctuation with Built in Over Load (TR Series) and Thermal Cut off Protections.
• Hot Start facility for easy arc striking (TR Series)
• Increased versatility with better utilization.

SHUNT CONTROLLED

Model	400cc	600cc
Input Voltage	415 ± 10%V/3Ø	415 ± 10%V/3Ø
	50 Hz	50 Hz
Max KVA	28 KVA	43.2 KVA
OUTPUT
Current	40A - 400A	60A - 60A
O.C.V.	85VDC	85VDC
Current at 60%	400A	600A
Current at 100%	300A	420A
Insulation	'H'	'H'
Cooling	Forced Air	Forced Air
L x W x H(mm)	990 x 585 x 765	1065 x 715 x 890
Weight	250 Kgs	350 Kgs

THYRISTORISED

Model	400TRcc	600TRcc
Input Voltage	415 ± 10%V/3Ø	415 ± 10%V/3Ø
	50 Hz	50 Hz
Max KVA	22.5 KVA	32 KVA
OUTPUT
Current	10A - 400A	10A - 600A
O.C.V.	100VDC	100VDC
Current at 60%	400A	600A
Current at 100%	320A	480A
Insulation	'H'	'H'
Cooling	Forced Air	Forced Air
L x W x H(mm)	480 x 580 x 850	520 x 625 x 900
Weight	130 Kgs	175 Kgs

MIG WELDING MACHINES - MIG INVERTER
The most economical Welding machine
An answerp to your need from the 'elektroweld' range of Equipments.

• Portable, Compact and Light Weight.
• Excellent Arc Characteristics on both solid and Flux Cored Wires.
• Delivers smooth and stable arc even at Lower Current.
• Save Electricity Cost.
• Unique lntegrated Adjustment Control offer automatic control in Welding Current when arc voltage is changed due to hand movement.
• Very Low spatters due to efficient power source.
• Fresh Arc Start, Smooth and optimum bead shape.
• 100% Indigenous & Service possible up to component level in Printed Circuit Boards.
• Capable of welding all types of metal like SS, MS, & Al etc. An excellent machine for Mig Brazing application also.
• Digital Amps and Volts Meter for accurate and precise setting.

WIRE FEEDER
• Low Inertia and High Torque Printed Circuit Motor allows very smooth wire feeding.
• Dynamic braking is controlled through Transistor switching ensures the longer life of Motor with min overrun of wire.
• Very Light Weight Wire Feeder weight only 9 Kgs.
• Aluminum Cast Feed roll block with single pressure touch system for various dia of wires.
• Remote control mounted on the Wire feeder eliminates the use of remote control cable thus increased reliability and min chance of breakdown.

MASTER WELDING MACHINE-MEGAMASTER AND MINIMASTER
The most economical Welding machine
An answerp to your need from the 'elektroweld' range of Equipments.

• Very Low Power Consumption. Saves Electrical power up to 50%.
• Compact, Light Weight & Portable machine.
• Protective Function against Over Voltage, Under Voltage, Over Heat and faulty Input supply.
• Current limiting function on short circuit of out put terminals.
• Constant Current Power Source.
• Extremely low NO LOAD POWER CONSUMPTIONS approx 100 Watts .

WELDING FEATURES
• Fine Arc Start, smooth and optimum bead.
• Higher metal recovery due to very low spatter.
• Anti Stick Device to protect electrode freezing.
• Compatible for welding of all types of electrode including rutile, Basic, SS, Copper etc.
• Excellent Power Source for Tig Welding(Scratch Start) or can be coupled with HF Unit specially designed for Inverter Power Sources.
• Preset Weld current control.
• Hot Start in built.
• Digital Amps meter for precise setting of Current.
• Constant Output welding current due to close loop feed back circuit.

MAINTENANCE FEATURES
• 100% Indigenous. Makes repairs possible up to PCB Component level.
• Control and Power Circuits separated in two chambers for easy maintenance.
• Easy accessibility for replacement of any component.
• MCB Provided in the input circuit for safety.