HEIGHT CONTROLLER * Integreted with mechanical lifting device and height controller.
* All Digital Technology. SMT in internal circuits ensures high reliability.
* Avdavnced height linear calibration technology makes precision error within ± 0.1mm.
* One-butten calibration for measure and calibration of absolute height.
* Easy to use. With two keys, height and level ofd sensitivity, you can complete the THC parameter set.
* Integrated with detector, controller and driver.
* Effective stroke as long as 30cm.
* lntelligently detect and directly display torch height under the capacitance mode with a high precision u to 0.1mm.
* Multiple interfaces suitable for any brand of plasma or flame cutting machine cnc system, independent use is ok.
* Stepper motor rather than DC motor makes control faster and more stable as well as extends product’s life.
PRECISION TRACK Precision machined, hardened, heavy duty deive rack on both the long and the cross travel direction, ensure high accuracy and long service life.
HEAVY DUTY RAILS
Carefully machined heavy duty rails give accuracy and stability to the machine for the whole working life.
LOW PROFILE DESIGN Hose and cable supply on the machine is via cable drag chain, keeping hoses and cables intact when cornering at critical speed
PATENTED QUALITY Ensure maximum rigidity, light weight and superb dynamic performance even at high speed.
CNC - MAJOR CANTILIVER
CANTILEVER TYPE: 1) Compnse of:
(a) 5.7 high-definition Lattice L.C.D. display.
(b) High speed 16-bit single-chip microcomputer & Hardware interpolator
(c) Stepper Motor with high subdivision control for smooth Movement & Low
2) Cutting Length- 3000 mm., can be increased in future. Cutting Width
3) 64 user programs can be loaded in machine, each program of maximum
4) Machine can be operated in Automatic or Manual mode.
5) It is very user friendly to load, edit, view or delete the programs
6) Cutting simulation can be seen on the screen of the machine.
7) Cutting parameters & location of torch can be monitored on screen.
8) Shape being cut can be zoomed & navigated.
9) Cutting can be resumed in case of Power Failure from the stopped point
if the location of torch is not displaced.
10) Improperly or incompletely cut part can be reworked without hassle
or Disturbing currently run program.
11) Compensation can as well be given during running of the Machine.
12) Cutting parameters can be set at any moment by pausing the machine
13) System can be diagnosed for output & input parameters at any
14) Machine Automatically takes Starting Point as the reference point.
15) Torch height can be adjusted manually or by machine controls.
16) Auto lgnition(optional) for gas cutting.
17) Motorized Cutter Post.
BOOM The cross boom
made of heavy sections of extruded Aluminium,
is supported at both the ends with LM guide
brackets and Teflon rollers base. Due to this,
there is virtually no sag when the boom is
fully protruding out for cutting requirement.
This also enhances the cuttingwidth. lt is
sufficiently strong to hold all the gas hoses & electricity
cable passing thru it. lts also helps in faster
travel of the machine in non cutting mode thereby
increases the productivity.
DUTY CUTTING TORCH
duty cutting torch fitted with all flash back
arrestor is not only safe to operate but also
can cut a thickness up to 200mm in clean cut.
Low voltage and high torque Motor of the Cutting
Torch Post helps in maintaining the torch height
accurately with job with out compromising the
safety to operator.
DUTY RAIL BASE A very Heavy duty
Rail Base made out of M.S. Square pipes and
machined M.S. Flats, fitted with LM rail and
Rack, support the total system. The mass of
the rail base helps to keep the machine totally
jerk free while in motion, even during the
environmental vibrations which are caused by
operation of other machines like Power Presses,
Heavy Machine tools etc. This gives the most
accurate cut which can be matched with any
Heavy duty Gantry type of CNC Cutter. lt helps
in faster movement during idling thereby increasing
SOFTWARE Software : Cutting
software supplied with the machine is the
most user friendly and is very easy to
operate. It helps not only in nesting but
also generating various cutting codes with
reports on utilizations on plate in terms
of mass of the cut components and % age
of the available plate.